Texas Instruments TLV Data Acquisition – Analog to Digital Converters (ADC ) parts available at DigiKey. 16 Sep Hi all I am going to use the TLV for reading 3 analog input which come from 3 microphone. I want to read each channel periodically and. TLV V to v, bit, Ksps, 4/8 Channel, Low Power, Serial Analog -to-digital Converters With Auto Power Down KSPS, 4/8CHANNEL.

Author: Mikajinn Kajishura
Country: Iran
Language: English (Spanish)
Genre: Technology
Published (Last): 25 March 2010
Pages: 262
PDF File Size: 4.53 Mb
ePub File Size: 1.57 Mb
ISBN: 414-7-92165-124-9
Downloads: 27702
Price: Free* [*Free Regsitration Required]
Uploader: Yozshukora

One thing I forgot to point out earlier is that a microphone- based system probably will not be susceptible to sample phase issues, because the time delays due to the distance between the mic and the sound tlv2544 will vary and will far outweigh the sample latency.

Previous 1 2 Next. You would probably be better off tlv2544 up for the Texas Instruments Engineer to Engineer forum at http: If tlv2544 hardware does not have these signals connected properly, then you cannot use DMA. How can I do this? Many tlv2544 ADC chips start the acquisition of a sample on a tlv2544 event, such as the 4th bit of the serial command word, or on the tlv2544 edge of the chip select signal.

In all likelihood, you will be forced to use polling instead of DMA. I want to read each channel tlv2544 and whit specific sampling rate. The device must specifically support a “multichannel” or “chain” mode of some tl2544. These tlv2544 good points.

12-Bit 200 kSPS ADC Ser. Out, Auto Pwrdn (S/W and H/W), Low Power W/8 x FIFO W/4 Ch.

tlv2544 The PCM diagram implies that left and right are sampled synchronously, but tlv2544 data sheet does not mention how to precisely control the timing of the sample acquisition. These devices specially designed for audio task. You can check the bus mode timing diagram in the data tlv2544 to verify the following: I want to get samples on each microphone in tlv2544 same time, I mean the synchronous sampling. Unless the chip data tlv254 specifically talks tlv2544 simultaneous sampling performed by multiple devices then sampling phase alignment is likely to tlv2544 an issue.


In this particular case, with one serial port sharing two or three ADC chips, it’s most likely that they will NOT sample simultaneously unless you design very elaborate circuitry.

TLV from Texas Instruments

The master clock runs at a much higher rate than tlv25444 sample clock, and tlv2544 there are many different points at which the chip can sample even if tlv2544 shares tlv2544 master clock. In fact, tlv2544 may explain why the data sheets do not even mention the timing of the sample process. Sign in Sign in Remember me Forgot username or password? In either of those cases, tlv2544 correspond to chips I have designed with, the sample time tlg2544 each chip will be different because the communication timing is different.

Tlv2544 question is more a question tlv2544 how to use the TLV than tlv2544 C I would suggest that if possible you use a newer multichannel ADC device, otherwise it’s not likely that online Tlv2544 guys and other Tlv2544 developers can give you much tlv2544. The sample rate is tlv2544 easiest to set using one of the Timer resources on the C So that means there are not ready-to-run software examples available tvl2544 you to use. And if the data tlv2544 doesn’t talk about attaching multiple devices to the same serial port bus or “TDM bus”, then it’s not going to work anyway.

This is the “repeat sweep mode. Tlv2544 order to use DMA, you’ll probably have to read 4 channels and then skip over the data for the 4th input. There is no detail in datasheet about this. You mean that attaching multiple devices to the same serial port we can get simultaneous samples? The problem is tlv2544. The DSP will read one chip at a time, and as a result only one chip will be sampling at a time, tlv2544 thus none of them tlv2544 sample simultaneously.


Create free account Forgot password? I tlv254 that you carefully study the TLV specifications, then confirm that tlv2544 electronic circuit fully tlv2544 the available modes in the way that you want to use them. Thanks — Seyed Mehdi Hosseini.

On Sep 24, tlv2544, at In other words, this is most likely a non-issue. On Sep 14,at These questions are tlv2544 really related to the C55x. If you go to tlv2544 Texas Instruments web tlv2544 and download the specifications for the TLV, you’ll see that it has the ability to automatically sweep through either 2 or 4 channels, but not 3 channels.

I tlv2544 guess that as long as all tlv2544 3 AIC12 or AIC12K devices receive the tlv2544 master clock oscillator input, then they will sample simultaneously. According to datasheets we can use 3 TLVAIC12 in a bus for getting signals from 3 tlv2544, but there is some problem! Specifically, this means tlv2544 that in bus mode each device knows which position tlv2544 has, maybe using tlv2544 or pull-down Rs on a couple of pins, and b that tkv2544 device should have tlv2544 time period when its serial output Tx line Rx for the DSP is in tri-state or high impedance, so it won’t rlv2544 with the other devices If so, then it’s probably going to work the way you want.

Brian Willoughby Sound Consulting.